2026-06-24Views：
You don't need to drain a drop every time, but drain it until you can't see obvious water.
First say why traditional air compressor drainage. After the air is compressed, the water vapor inside will become condensed water, which will sink to the bottom of the gas tank or separator. If it is not drained, the water will accumulate more and more, and finally run into the air-using equipment with compressed air, resulting in rust of pneumatic tools, instrument failure and product contamination. Therefore, drainage must be done, but there is no need to pursue absolute drainage. It is enough to drain the water at the bottom below the lowest water level, leaving a thin layer of water film.
Then when must it be completely arranged. Be sure to clean before stopping. Because the temperature drops after the machine stops, the residual water will condense again. If it is not drained, the water will be directly brought into the pipe network when the machine is turned on next time, causing water to be brought in the first breath. In addition, if the ambient humidity is extremely high and condensate is generated quickly, and the water level is found to have reached the warning line during the inspection, then don't wait and drain it immediately.
When the water-lubricated air compressor is involved in the work, the logic of drainage is not the same. The water-lubricated air compressor uses clean water instead of lubricating oil. The water forms a water film inside the machine to reduce friction and seal gaps. The compressed air-water mixture is separated and the water is recovered for recycling. Therefore, its water is the working medium, not the waste liquid, and cannot be completely discharged. What needs to be discharged is the excess condensed water separated from the air. This part of water is separated from the circulating water and should be discharged from the drain valve regularly. However, the part of the water involved in lubrication and sealing inside the machine must be retained, and only the separated one will be discharged when discharging. Never drain the water in the circulating water tank, otherwise the machine will have problems when running dry.
In short, the traditional air compressor drainage is to discharge waste water, which is as clean as possible but not serious. Water lubricated air compressor drainage is the discharge of excess condensed water, circulating water to stay. Either way, stopping the front row once is the most basic operating habit.
In the blow molding process, the typical range of compressed air pressure is 0.2~1.0 MPa, and the specific value needs to be dynamically adjusted according to the type of plastic, parison temperature, product structure and process requirements. By providing clean, oil-free compressed air, oil-free air compressors become
Calculating the air consumption of an air compressor involves multiple steps and factors. The following is a rigorous and detailed calculation method: 1. determining the work demand First, the work demand of the air compressor needs to be clarified, including the required working pressure and flow. Working pressure refers to the air compressor output gas
The quality requirements of medical compressed air are very strict to ensure the safety and health of patients. The following is a detailed summary of the quality requirements of medical compressed air: 1. cleanliness requirements: medical compressed air must meet the cleanliness requirements, especially in
Regarding the maintenance cycle of the air compressor, the exact time is not static, but is affected by many factors, including the type of air compressor, the use of the environment, the workload and the manufacturer's recommendation. The following is a general guide to the air compressor maintenance cycle: air compressor
The quality of the air entering the fermenter is critical to the success of the fermentation process. Granklin Group, as a well-known air compressor manufacturer, provides water-lubricated air compressors and oil-free air compressors to meet the demand for high-quality air in the fermentation industry.
To obtain oil-free compressed air, the following methods and technologies can be used: 1. Definition and principle of using oil-free air compressor: oil-free air compressor does not use lubricating oil during compression, thereby avoiding lubricating oil entering Compressed air, directly output low oil or connected
The power range of water lubricated air compressor is usually 7.5-250KW. This power range can meet application scenarios of different sizes and needs, from small industrial equipment to large production lines, where suitable water-lubricated air compressors can be found. About Hagrid
The replacement cycle of the air filter element of an air compressor depends on a number of factors, including the use environment of the air compressor, the working load, the air quality and the quality of the filter element. Typically, the replacement cycle of the filter element can vary from weeks to months. in a harsh working environment
Medical air compressor (air compressor) plays an important role in the medical field. Its core is to provide stable and clean compressed air for medical equipment to support the needs of various medical scenarios. The following are its main functions and application scenarios: 1. Driving medical equipment respiratory support
Large oil-free air compressors are widely used in a variety of fields with high air quality requirements because they do not contain oil in the compressed air, including but not limited to the following: Electronic industry: oil-free air compressors can continuously provide clean compressed gas
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
