2026-06-24Views：
The pressure of the equipment is generally set at 4 to 6bar, and the core reason is three words, which is enough.
Let's talk enough about this first. In the vast majority of gas-using scenes in the factory, the pneumatic wrench screws, the cylinder pushes and pulls, purges and cleans dust, and controls the gas supply to the instrument. These jobs do not require much effort at all. The air pressure of 4 to 6bar is more than enough to push up, and then add pressure, the speed and effect of the tool work are almost the same, which is a waste.
And save the electricity. Every time the air compressor presses a little more, the motor will consume an extra share of electricity. From 4bar to 6bar, the power consumption will increase significantly, but the work effect will not be improved. Therefore, 4 to 6bar is the most cost-effective range, which can not only do a good job, but also prevent the electricity bill from running away in vain.
And the security thing. The higher the pressure, pipe joints, hoses, valves, these places are more prone to problems. The range of 4 to 6bar is very friendly to most pipes and seals. It is not easy to leak, and it is not easy to flush the interface. Daily maintenance is much less troublesome.
In addition, most of the pneumatic components on the market, from solenoid valves to cylinders to connectors, are designed according to this pressure range when leaving the factory. You can match it directly after you buy it, without extra selection, which is one of the reasons why everyone relies on this range.
When the water lubricated air compressor is involved in the work, the output can also be compressed air in this range (the pressure of the water lubricated air compressor produced by Shanghai granklin group can reach the range of 0.3-4MPa). The water-lubricated air compressor uses clean water instead of lubricating oil. The water forms a water film inside the machine to reduce friction and take away heat, and finally outputs clean, oil-free compressed air. When it supplies air to scenes requiring air quality such as food processing and electronic manufacturing, the pressure is also set at 4 to 6bar, because the equipment in these scenes does not need more pressure and is enough. The water lubricated air compressor operates in this pressure range, and with the characteristics of oil-free output, it not only meets the production needs, but also ensures the cleanliness of the gas end, and completely matches the gas demand of ordinary equipment.
Therefore, 4 to 6bar is not set casually. It is a mainstream range naturally formed by the combination of factors such as sufficient use, power saving, safety and easy purchase of accessories.
Single screw water lubricated air compressor does not require refueling. This air compressor adopts oil-free water lubrication technology, and its lubrication and cooling medium is water instead of traditional lubricating oil. The following is a detailed explanation of the single screw water lubricated air compressor that does not need refueling: 1. working principle
Oil-free air compressor has the advantages of low failure rate, high quality air compressor and stable product performance. In order to ensure its working efficiency and equipment service life, the following points should be paid attention to when using: 1. When using an oil-free air compressor, a compressor must be set to protect the grounding wire
The calculation of the hourly compressed air consumption of the equipment needs to comprehensively consider the factors such as equipment parameters, operation mode, system efficiency and actual working conditions. The following are the specific calculation methods and steps: 1. the basic formula of compressed air consumption (Nm & sup3;/h) = theoretical air consumption of the equipment
In the process of food production, compressed air is an important auxiliary tool, which is widely used and critical. However, the issue of whether compressed air can come into direct contact with food is related to food safety and product quality and must be treated with caution. Shanghai Granklin Group
The oil content standard of compressed air for general industrial use is usually not more than 0.01 mg per cubic meter (ISO 8573-1 level 1 or GB/T 13277.1-2023 level 1), and some scenarios can be relaxed to 0.1 mg (level 2). The following are specific instructions: 1. international standards (ISO 8
Air compressors are usually designed to work continuously, but whether they can continue to operate stably depends on many factors, including the quality of the equipment, manufacturing process, use environment, workload, and maintenance. For high-quality air compressors, if appropriate
The price of screw air compressor repair varies due to a variety of factors, including brand, model, fault type, repair scope, and service provider's pricing strategy. The following is some analysis and summary of the maintenance price of screw air compressor: 1. price range
The permanent magnet frequency conversion screw air compressor has a good performance in many brands. Which brand is of good quality needs to be judged according to the specific needs and evaluation criteria of users. The following are some excellent brands in the field of permanent magnet frequency conversion screw air compressor:
In chip manufacturing, the control of gas pressure and purity needs to be realized through precise adjustment technology, multi-stage purification process, real-time monitoring system and the core equipment of oil-free water lubrication air compressor. This type of air compressor uses water as the lubricating medium to eliminate the risk of oil pollution from the source. With intelligent control and whole process risk management, it can stably output high-pressure and high-purity gas, providing key guarantee for chip manufacturing.
The drainage process of the screw air compressor can be carried out through the following steps: Manual drainage method: First, tighten the drainage valve and turn off the oil pump. Next, the pressure relief valve knob is rotated counterclockwise to relieve the pressure inside the reservoir. Open reservoir
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
