2026-06-22Views：
Will be bad. If the screw air compressor is not used for a long time, various problems will occur slowly inside, and the longer the time, the more serious the damage will be.
The main bad in four places. First, the oil will deteriorate. If the oil-lubricated machine is stopped for a long time, the oil will oxidize, thicken and even agglomerate. When the machine is turned on again, the oil circuit will be blocked and the machine will be strained as soon as it turns. Second, the seal will age. The rubber ring inside does not move for a long time, it will slowly harden and lose its elasticity. If it is turned on again, it will leak air and the pressure will not go up. Third, the motor is susceptible to moisture. When it is stopped, the moisture in the air will drill into the motor coil, the insulation performance will decrease, and it may burn as soon as it is powered on. Fourth, metal parts will rust. Screw and bearing long-term contact with humid air, the surface will be oxidized, and the friction will increase and wear will accelerate when running again.
Water-lubricated air compressors have an obvious advantage in this matter. Because it uses water instead of oil for lubrication, there is no problem of oil deterioration and agglomeration. If the water is drained before it is idle, the oil sludge will not be left inside to block the oil circuit. Moreover, the gas discharged from the water-lubricated air compressor does not contain oil. If the residual water inside is discharged in time after shutdown, the metal parts will rust slower than the oil-lubricated machine.
But the water lubricated air compressor can not be completely ignored. The seal will also age, and the motor is also afraid of moisture, so even if it is not used for a long time, it is recommended to power on the machine every once in a while to let the machine idle for a while and bake the internal moisture.
In general, long-term idleness will definitely be bad, but the water-lubricated air compressor has less oil deterioration and the overall damage is lighter than that of oil-lubricated machines, and maintenance is more worry-free. If you want to know what preparations should be made before you are idle, you can continue to talk.
The pressure range of compressed air for industrial use varies depending on the application scenario and the type of equipment, but there are usually the following standards: 1. General industrial pressure range General standard: The pressure of compressed air for industrial use is usually between 0.7 and 1.0 megapascals (MPa), which is suitable for most industrial scenarios.
There is no direct difference between oil-free air compressors and oil-free air compressors in terms of durability. They have different characteristics and application scenarios, so which is more durable depends on the specific use environment and maintenance conditions. The advantage of oil air compressor is
Screw air compressors are generally not recommended for frequent start-up. Frequent start-up may cause additional burden and wear on the electrical system, motor and mechanical parts of the air compressor, shortening its service life. In addition, the current impact at startup may also stabilize the grid.
The application of nitrogen in semiconductor processing and its role in semiconductor processing, nitrogen (N₂) plays a vital role. Its unique chemical and physical properties make nitrogen an integral part of semiconductor manufacturing. The following is nitrogen in the semi-conductor
The air pressure standard for the production workshop is not fixed, but is determined according to the specific application scenario and equipment requirements. The following are some common air pressure standards for air used in production workshops and related information: Standard atmospheric pressure: In industrial production, commonly used
The compressed air used in the production of puffed food must be clean air that does not contain oil, has very low moisture, has no dust and bacteria, and has no peculiar smell. Water lubricated air compressor is becoming a more and more popular gas supply choice for food production enterprises because it solves the problem of oil pollution from the source.
The maintenance cycle of air compressors will vary depending on the equipment model, the use environment, the workload and the manufacturer's recommendations. Generally speaking, air compressors require regular daily inspections, preventive maintenance and regular maintenance to ensure their normal operation and
The air compressor is indeed one of the main equipment of the power plant. It is responsible for key tasks such as soot blowing, gas supply for instruments, driving valves and tools, which directly affects the safety and efficiency of the power plant. The water-lubricated air compressor is becoming an increasingly popular solution in the power plant air supply system because it replaces oil with water, making the output air cleaner and easier to maintain.
Air compressor safety measures mainly include the following: installation of exhaust valve: effective control of pressure release, to prevent excessive pressure caused by explosion. Regular inspection and maintenance: to ensure the normal operation of the air compressor, reduce the occurrence of failures and accidents. Check contents
Frequency conversion screw air compressor and power frequency air compressor are two common compressed air equipment in the industrial field, each of which has different characteristics and application scenarios. The following is a detailed comparison of these two air compressors: 1. working principle of variable frequency screw air pressure
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
