2026-04-09Views：
Screw air compressor is a widely used general machinery and plays an important role in all walks of life.
Daily mastering the correct operation method can prolong the life of the screw air compressor. So what is the daily operation of the screw air compressor? What should I pay attention?
1. screw air compressor boot
1) Turn on the power supply and check whether the power indicator is on.
2) Press the start button, the main controller automatically controls the loading and unloading of the air compressor.
3) Check the oil level during loading, and the oil must be between the upper and lower lines.
4) During the operation of the machine, the temperature displayed on the panel will rise accordingly. When it reaches 90 degrees, the fan will automatically start, and when the temperature drops to 75 degrees, the fan will stop.
Shutdown of 2. screw air compressor
1) If there is no gas for a long time and there is no air leakage, the air compressor will automatically stop after 30 minutes of no-load operation. At this time, it shows that the machine will stop for too long. When it is lower than the loading pressure, the machine will automatically load and run.
2) Manual shutdown Press the red stop button to load the indicator light goes out, and the air compressor will stop after unloading and running for 10-30 seconds. After manual shutdown, it must be manually started to run.
3. screw air compressor start and stop sequence
startup: air compressor-cold dryer; Shutdown: cold dryer-air compressor
4. considerations
1) Always check whether there is oil leakage inside the air compressor. If there is a large area of oil leakage, it should be stopped immediately.
2) Use compressed air to blow the dust in the air filter and the cooler above the air compressor every week to ensure that less dust enters the compressor head and good heat dissipation effect.
3) Discharge the moisture in the gas storage tank every week to avoid excessive moisture entering the gas pipeline.
4) The new machine runs for 500 hours and needs to replace the oil filter, lubricating oil and air filter, and then replace it every 2500-3000 hours.
5. air compressor prone to failure
1) High temperature shutdown:
the machine is short of oil-add lubricating oil to the correct position; the radiator is blocked-use compressed gas to blow the dust inside; the oil filter is blocked-replace.
2) When the voltage exceeds 350-420V, the machine will automatically protect and stop.
3) The cold dryer in the compressed air post-processing equipment cannot be started.
Whether the air compressor needs to run all the time depends on the specific application scenario, equipment type, operation requirements and energy management strategy. The following is an analysis of its operation mode and application from different angles: 1. Scenarios requiring continuous operation Continuous gas supply demand
As an important industrial equipment, air compressor has a wide range of applications. The following is a summary of the applicable industries of air compressor: machinery processing industry: in the machinery processing industry, air compressor is one of the essential equipment, it is widely used in the processing center program control
The main difference between micro-oil screw compressors and oil-free screw compressors is whether they use lubricating oil during their work, and the resulting differences in performance and application. Use of lubricating oil: micro-oil screw compressor: this type of compressor
The air compressor can reach a pressure of 30MPa, but this kind of equipment belongs to the category of high-pressure air compressor, which is usually used in specific industrial or professional fields. The following is a detailed analysis: 1. technical feasibility of high-pressure air compressor technology to achieve There are already on the market specifically designed to produce high
The nitrogen-making machine can continuously produce nitrogen without interruption, which is mainly due to its design principle, technical characteristics and the stability support of the air circulation system, the specific analysis is as follows: 1. design principle supports the continuous nitrogen-making machine through physical separation technology (such as pressure swing adsorption PS.
Air compressor is not special equipment. Special equipment refers to the equipment involving life safety and high risk, including boilers, pressure vessels (including gas cylinders), pressure pipes, elevators, lifting machinery, passenger ropeways, large amusement facilities and special maneuvers in the field (factory).
Q: air compressor and compressor is the same? A: not the same although the two names are similar, and even the name is no difference, the difference in the application scenario is very big. For example, compressors used in refrigerators and air conditioners, and screw and piston air compressors
The air pressure (pressure) of the air compressor is usually set according to the specific application scenario to meet the gas demand of different industries. In common industrial scenarios, the output pressure of air compressors is mostly concentrated between 0.8MPa and 1.5MPa (I .e. 800,000Pa to 1,500,000Pa), which can be covered.
Air compressor export oil content standards are usually formulated by the International Organization for Standardization (ISO) or related industry associations. For example, ISO 8573-1 is an important standard for oil content testing of air compressors, which specifies three levels of oil content: oil content ≤ 0.01 mg/m &
Regarding the total number of colonies of oil-free air compressor compressed air, this question relates to the type of air compressor and its impact on air quality. The following is a detailed answer to this question: the characteristics of oil-free air compressor: oil-free air compressor adopts oil-free lubrication
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
