2026-04-10Views：
Screw air compressor safety operating procedures mainly include the following:
preparation before 1. start:
operators must be familiar with the structure, performance, working principle, operating procedures and precautions of the air compressor, and after technical training and safety training, after passing the examination, they can be certified to work, and those without a license are not allowed to work.
Check the capacity of lubricating oil in the oil-gas separator. After normal operation, the oil level in the oil level gauge is the best if it is above the middle of the upper and lower limits.
Check whether the air supply pipeline is unblocked and the joint is firm.
Check whether the various instrument indications on the low-voltage power distribution cabinet are normal, whether the electrical wiring is intact, and whether the grounding wire meets the standards.
Before starting, the operator should be in a safe position, open the air compressor exhaust valve and close the manual drain valve.
Note in 2. operation:
check whether the indications of various electrical instruments are normal.
Check whether there is any problem with the sound of each part of the machine.
Check whether the lubricating oil level is normal.
When replacing the oil and gas separator, be careful to discharge static electricity.
The screw air compressor shall operate within the rated pressure range and the discharge temperature shall not exceed 110 ℃.
When the compressor is running, there shall be no abnormal sound, air leakage or oil leakage.
The compressor shall not be operated in an area where the oil level is lower than the line under the second red line of the oil level gauge. If this phenomenon occurs, stop the machine immediately for refueling.
If it is found that the instructions are incorrect or abnormal, it should be replaced or shut down for maintenance in time.
3. shutdown operation:
press the stop button, after the delay unloading, the unit will stop. If there is an abnormal situation, press the "emergency stop" button to carry out emergency stop.
After shutdown, cut off the power supply and close the air supply valve of the air compressor. Drain water from coolers, oil-water separators, exhaust lines and air bags.
When the machine is shut down for maintenance, the knife switch of the power cabinet must be opened and listed, and grounded.
The above is the screw air compressor safety operation procedures, I hope to help you. In actual operation, please pay attention to safety and follow the procedures.
In today's industrial production, air compressor as an important power equipment, its performance and efficiency is directly related to the production costs and benefits of enterprises. Especially in the application of frequency conversion technology, a high-quality frequency conversion air compressor can save energy and reduce consumption for enterprises, improve production
Factory air compressor conventional air pressure: In the factory environment, the conventional air pressure of the air compressor is usually determined according to the specific application requirements. Generally speaking, the output pressure range of industrial air compressors is 5-13 bar (I .e. 500-1300 kPa or 72.5-188.5 psi)
When discussing whether the screw air compressor can reach 13 pressures (I. e., about 1.3MPa or 13bar), we have to mention the water-lubricated screw air compressor produced by Shanghai Granklin Group. As a well-known brand in the industry, Granklin Group has been committed to air compressor technology.
The air compressor is oil-free, but the specific choice should be judged according to the actual demand and application scenario. The following is a brief description of the oil-free air compressor: The oil-free air compressor avoids the use of lubricating oil to ensure the purity of the compressed air. This is
the role of air compressor in construction site analysis 1. core power source: drive pneumatic tools 1. typical pneumatic equipment support drilling and cutting: air compressor for pneumatic drill, pneumatic hammer and other tools to provide high pressure air, make it in concrete, rock and other hard materials
Medical air has many important uses in medical facilities. The following is a detailed summary of its uses: Clean and purify air: Medical air is filtered, sterilized, and purified, which can effectively reduce bacteria, viruses and other pollutants in the air. Ensure
The role of compressed air in the operating room: In the operating room, compressed air plays a vital role. It is mainly used to drive various medical equipment and tools, such as scalpels, drills, saws, staples, etc. It also provides clean and dry space for the operating room.
Deoiling and dehumidification of compressed air is the core link to ensure the precision of industrial production and the reliability of equipment operation, which needs to be realized by combining source control and post-processing technology. The following from the specification requirements, technical path and industry application of the three aspects of the system.
In the use of air compressors, the choice of power frequency or frequency conversion mainly depends on the specific application requirements and energy efficiency considerations. The following are some considerations about power frequency and variable frequency air compressors: Power frequency air compressors: run at a fixed speed, usually by turning on or
In the semiconductor industry, due to the particularity of the production process and the high requirements for air quality, oil-free air compressors are usually recommended. Oil-free air compressor can avoid the pollution of compressed air caused by lubricating oil, so as to ensure the stability of the production process and product quality
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
