2026-04-10Views：
Screw air compressor is how to maintain it?
We can look at the maintenance case of single screw air compressor in Dengfeng, Henan Province, and quickly understand how air compressor personnel maintain screw air compressor through explanation.
Screw air compressor maintenance:
1. Intake air filter element
the air filter is a component that filters out air dust and dirt, and the filtered clean air enters the compression cavity of the screw rotor for compression. Because the internal clearance of the screw machine only allows particles within 15u to be filtered out. If the air filter element is blocked and damaged, a large amount of particles larger than 15u will enter the screw machine to circulate, which will not only greatly shorten the service life of the oil filter element and the oil fine separation core, but also cause a large amount of particles to directly enter the bearing cavity, accelerate the bearing wear and increase the rotor gap. The compression efficiency is reduced, and even the rotor is boring and seized.
2. Oil filter
after the new machine runs for 500 hours for the first time, the oil core should be replaced, and the oil filter element should be removed with a special wrench. It is better to add screw oil before installing the new filter element. The filter element seal should be screwed back to the oil filter seat with both hands and tightened firmly. It is recommended to replace the new filter element every 1500-2000 hours. It is best to replace the oil filter element at the same time when changing the oil. When the environment is bad, the replacement cycle should be shortened. It is strictly prohibited to use the oil filter element beyond the time limit. Otherwise, due to the serious blockage of the filter element and the pressure difference exceeding the bearing limit of the bypass valve, the bypass valve will automatically open, and a large amount of dirt and particles will directly enter the screw main engine, causing serious consequences. Diesel screw machine diesel engine oil filter and diesel filter replacement should follow the diesel engine maintenance requirements, the replacement method is similar to the screw oil core.
3. Oil and gas separator
the oil-gas separator is a component that separates the screw lubricating oil from the compressed air. Under normal operation, the service life of the oil-gas separator is about 3000 hours, but the quality of the lubricating oil and the filtration accuracy of the air have a huge impact on its life. It can be seen that the maintenance and replacement cycle of the air filter element must be shortened in the harsh use environment, and even the installation of a front air filter is considered. The oil and gas separator must be replaced when it expires or the pressure difference between the front and rear exceeds 0.12Mpa. Otherwise, the motor will be overloaded and the oil and gas separator will be damaged and oil will run. Replacement method: Remove the control pipe joints installed on the oil and gas barrel cover. Take out the oil return pipe extending into the oil and gas barrel on the cover of the oil and gas barrel, and remove the fastening bolt of the upper cover of the oil and gas barrel. Remove the upper cover of the oil and gas barrel and take out the oil. Remove the asbestos pads and dirt stuck to the upper cover. Install the new oil and gas separator, pay attention to the upper and lower asbestos pads must be stapled, and the asbestos pads must be neatly arranged when pressing, otherwise it will cause pad punching. Install the upper cover plate, oil return pipe and each control pipe according to the original sample, and check whether there is any leakage.
4. Oil replacement
the quality of screw oil has a decisive influence on the performance of oil injection screw machine. Good oil has good oxidation stability, rapid separation, good foam cleaning, high viscosity and good corrosion resistance. Therefore, users must use pure screw oil for the company.
The first oil replacement will be carried out after the new machine runs in for 500 hours, and the new oil will be replaced every 2000 hours after operation. It is best to change the oil filter at the same time. Use in harsh environments to shorten the replacement cycle. Replacement method: start the air compressor to run for 5 minutes, so that the oil temperature rose to more than 50 degrees Celsius, oil viscosity decreased. Stop running. When there is 0.1Mpa pressure in the oil and gas barrel, open the oil drain valve at the bottom of the oil and gas barrel and connect the oil storage tank. The oil drain valve should be opened slowly to prevent the oil with pressure and temperature from splashing and hurting people. Close the oil drain valve after the lubricating oil becomes dripping. Unscrew the oil filter element, drain all the lubricating oil in each pipeline at the same time, and replace it with a new oil filter element. Open the screw plug of the oil filler, inject new oil to make the oil level within the range of the oil mark scale line, tighten the screw plug of the oil filler, and check for leakage. Lubricating oil must be checked frequently during use. When it is found that the oil level line is too low, new oil should be added in time. Condensate water must also be discharged frequently during use of lubricating oil. Generally, it is discharged once a week, and it should be discharged 2-3 days in high temperature climate. Once. Shut down for more than 4 hours, open the oil drain valve when there is no pressure in the oil and gas barrel, drain the condensed water, and quickly close the valve when organic oil flows out. It is strictly prohibited to mix different brands of lubricating oil, and avoid overdue use of lubricating oil. Otherwise, the quality of lubricating oil will decline, the lubrication will be poor, and the flash point will be reduced, which will easily cause high temperature shutdown and cause spontaneous combustion of oil.
As the screw oil-free and water-lubricated screw air compressor is a stainless steel single screw main machine for the whole series, it can save more than 15% energy than the secondary dry twin screw and more than 36% energy than the primary twin screw. Oil-free screw air compressor reaches the energy-saving level of oil machine. Avoid frequent and high maintenance of dry screw. Energy saving: Grankering single-screw main engine with high volumetric efficiency is adopted, which has low specific power and is more efficient and energy-saving than twin-screw oil-free air compressors.
Why frequency conversion air compressor maintenance is much more expensive? ● must use high-quality lubricating oil frequency conversion air compressor for lubricating oil quality requirements are far higher than the frequency air compressor, can not be used according to the frequency air compressor standard selection of lubricating oil. The reasons are as follows: 1. change
In the field of food production, compressed air is the key power source and process medium, and its quality is directly related to food safety and product quality. In order to ensure that compressed air meets the high standards of the food industry, it is necessary to control the cleanliness, oil-free, microbial and other dimensions.
Oil-free air compressor in the domestic products, with completely independent production capacity of the enterprise "Shanghai Grencklin Group". Localization in the field of oil-free air has improved the global market competitiveness of my country's air compressor products. A steady stream of "oil-free air" supplies domestic mid-to-high-end manufacturing and production gas to produce global commodities.
Compressed air can be pressurized, cooling, adsorption and other methods to remove the water vapor, and can be through heating, filtration, mechanical separation and other methods to remove liquid moisture. Refrigerated dryer is a kind of equipment that cools the compressed air to remove the water vapor contained in it and obtain relatively dry compressed air. The rear cooler of the air compressor also uses cooling to exclude the water vapor contained therein. Adsorption dryer is the use of adsorption principle to remove the water vapor contained in compressed air.
At present, the completely oil-free air compressor equipment that can be seen in the market mostly adopts two schemes: "water lubrication oil-free" or "dry oil-free". Different lubrication methods lead to great differences in power consumption and machine loss and maintenance of oil-free air compressors.
View detailsBusiness owners were confused about the choice of screw air compressor products in the early stage of factory construction, because during the factory construction process, they will definitely receive sample books from various manufacturers sent by many sales staff. Screw air compressor sales staff publicity
In the process of air compressor maintenance, one of the most common faults is the overload of the motor of the air compressor.
The primary maintenance of screw air compressor mainly includes the following contents and steps: 1. Check the joint contact and insulation resistance of the electrical part of the air compressor. First, use an ammeter to detect the current value of each item or use an infrared temperature measuring gun to detect the incoming terminal temperature. Do
Several advantages of oil-free air compressor, as well as the difference between oil-free air compressor and oil-free air compressor. Specifically, look at their differences: oil and no oil in the air compressor generally refer to the amount of oil content in the gas discharged from the exhaust port of the air compressor. Generally, the oil content of the oil machine is relatively large, and the oil content of the oil-free oil machine is 0.01ppm, so this oil content is used to distinguish the oil and no oil in the air compressor. There is also a full oil-free air compressor, it is not the use of oil lubrication, but the use of water lubrication, so the final discharge of the gas does not contain oil called full oil-free air compressor.
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
