2026-04-10Views：
In the past water plant construction, we generally choose the piston screw air compressor. The piston screw air compressor has the advantages of low investment cost and large compression ratio, but at the same time, the screw air compressor also has many moving parts, easy to wear, and large maintenance workload.
In the past water plant construction, we generally choose the piston screw air compressor. The piston screw air compressor has the advantages of low investment cost and large compression ratio, but at the same time, the piston air compressor also has many moving parts, easy to wear, and large maintenance workload.
There are two two-stage air-cooled oil-free piston screw air compressors, which have been in use for less than half a year. Various problems have arisen one after another, such as excessive wear of piston rings and pistons of piston air compressors, excessive wear of inlet and outlet valve plates and valve seats, and oil leakage of oil control system. Moreover, the air production of the piston air compressor is obviously insufficient, and the machine is in a loading state for a long time and cannot be unloaded, thus increasing its own wear.
Through extensive understanding of the screw air compressor and comparison, the final selection of the screw air compressor. After use, it is found that the screw air compressor is not only easy to operate, but once the various operating parameters of the screw air compressor are set, the screw air compressor can be completely controlled and monitored by its own computer controller.
These characteristics of the screw air compressor are related to the unique host structure and working mechanism of the screw air compressor, and are also closely related to the reasonable system design and intelligent electrical control system of the screw air compressor itself.
A prominent feature of the electrical control system of the screw air compressor is the high degree of intelligence, and the man-machine interface of the screw air compressor is simple and friendly.
It takes a computer controller and its control panel as the control center, takes the analog signal of the outlet temperature sensor of the compressor host and the pressure sensor of the air supply port of the screw air compressor and the switching signal such as motor overload as the main input, runs the built-in control program through the screw air compressor, and outputs the electrical signal to trigger the conventional electrical control element to realize the control of the screw air compressor.
From the main structure and working mechanism of the screw air compressor, it is not difficult to see that the screw air compressor has fewer moving parts. The screw air compressor has only a pair of intermeshing rotors (there is an oil film between the rotors). The screw air compressor does not have a reciprocating piston mechanism similar to a piston machine and a complex inlet and outlet valve mechanism, so the screw air compressor has little wear, more reliable operation and long life.
Secondly, the operation of the main engine of the screw air compressor is similar to that of the turbine machine. The screw air compressor has no unbalanced inertial force, and the gas compression of the screw air compressor is continuous without impact. The machine can work smoothly and at high speed without special equipment foundation.
In addition, the noise of the screw air compressor can be reduced to a lower level.
Granklin Group is a professional manufacturer of air compressors, providing professional technical guidance and after-sales service for air compressor users.
Screw air compressor common 35 fault solutions, 1, the pressure on the pipeline exceeds the rated load pressure, the pressure regulator is disconnected. There is no need to take measures. When the pressure on the pipeline is lower than the loading (position) pressure of the pressure regulator, the screw air compressor will automatically load; 2. If the solenoid valve fails, remove it for inspection and replace it if necessary;
The highly integrated, energy-efficient integrated mainframe produced by Shanghai Granklin Group comes from the Granklin Group Air Compressor Technology Research and Development Center. Water lubricated screw air compressor host, water vapor cylinder, water filter and air filter, intake valve, cold dryer, air storage tank, etc. are integrated into one, forming an integrated air compressor system. The built-in three filters are easy to maintain, and there is no pipeline loss inside. It takes up very little space and is the key first step to form a small lightweight air compressor; at the same time, it also provides enough maintenance space.
Minor maintenance only needs to replace the air compressor oil and oil filter, which is usually replaced after 500 hours of operation of the new machine. Major maintenance is carried out about 3000 hours of operation of the machine, and the air filter element of the air compressor, oil and gas separator core, motor grease, etc. Electric shift
High-end air compressors are basically monopolized by foreign brands, mainly: the price of the whole machine of major international brands is relatively expensive. Domestic products such as: granklin is not bad, the price of the whole machine is relatively cheap
Oil-free air compressor has two compression modes, water lubricated oil-free air compressor and dry oil-free air compressor. We need pure oil-free compressed air. Most of them purchase equipment in these two schemes. Water-lubricated air compressors are mature enough. Shanghai Granklin Group mainly produces water-lubricated air compressors.
View detailsAir compressors are used in electroplating plants: 1. Sand blowing before plating 2. Air blowing after plating 3. Products are used to spray varnish after plating 4. Some small tanks are also used for compressed air stirring. What equipment is needed to establish an electroplating plant
Air compressor is one of the general equipment in the manufacturing industry, and doing a good job of energy saving management of air compressor is a necessary work for enterprises to save electricity. In order to save the production cost of enterprises, enterprises equipped with high energy efficiency air compressor is imminent. So how to make the air compressor energy saving?
During the working process of the air compressor, the temperature will be too high. At the same time, when the air compressor is used for a period of time, it will be easily contaminated with dust, so it is necessary to regularly clean the air compressor and dissipate heat.
1. Check whether the fuse is burned and blown, causing the circuit to fail and cannot be powered on. 2. Motor failure. The insulation layer is aged or the temperature is too high, the insulation layer is melted, so that the insulation effect is insufficient and leakage occurs. 3. The motor is locked and overcurrent. Not enough lubricant,
Literally know that the permanent magnet variable frequency air compressor really saves electricity, we all know that the maglev train, is running by magnetic force, no resistance so the train running speed is particularly fast, the motor of the permanent magnet variable frequency air compressor is also
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
