2026-04-10Views：
The starting sequence of the air compressor can be slightly different according to different types of air compressors, but the following basic steps are usually followed:
turn on the main air switch: This is the first step to start the air compressor to supply power to the entire system.
Turn on the air switch of related equipment: Under the main air switch, there are usually air switches for air compressors, cold dryers, exhaust fans and other equipment. These switches need to be turned on one by one.
Start the air compressor:
first, open the emergency stop switch on the air compressor operation panel.
Press the reset key to remove the possible alarm.
Then, press the green start button to start the air compressor.
Open the drain valve of the air storage tank: after draining the accumulated water for about 5 minutes (subject to draining the accumulated water in the air storage tank), close the drain valve.
Start the cold dryer: after the air compressor is started, press the start button on the operation panel of the cold dryer to start the cold dryer, and the green indicator light of the cold dryer should be on at this time.
In addition, for some types of air compressors, such as screw air compressors, some additional preparations may be required before starting, such as checking the lubricating oil level, belt tightness, and whether the fastening bolts are loose. At the same time, pay close attention to the running status of the air compressor during the start-up process to ensure its normal operation.
Please note that the above steps are for reference only, and the specific operation may vary depending on the air compressor model and manufacturer. Therefore, before starting the air compressor, be sure to refer to the equipment manual or relevant operating instructions to ensure correct operation.
In addition, the air compressor and the cold dryer usually need to be opened and closed at the same time to ensure the normal operation of the system. If only the air compressor is opened without opening the cold dryer, a large amount of water vapor may enter the compressed air pipeline, which will affect the normal operation of the equipment.
Screw air compressor oil glue treatment methods mainly include the following: Cleaning method: First, you can try to clean the oil system to remove impurities and sediments. After cleaning, re-add new oil. This can effectively remove
At one atmospheric pressure, the concentration of water molecules in the air is closely related to temperature and humidity. The following is a detailed calculation and scientific explanation: 1. the core calculation principle, the concentration of water molecules in the air can be calculated by combining the ideal gas state equation with relative humidity: C = R & sdot;TP
Dry-type oil-free machine will not have oil, because its design principle and working process do not need to use lubricating oil. Dry-type oil-free machines usually use special materials and structural design to ensure that no lubricating oil is needed to reduce the temperature during the compression process
The quality standard of medical compressed air is usually stipulated by the national health department or industry standard. In China, the standard of medical compressed air is regulated by the "Hospital Compressed Air Quality Standard" (GB/T 14213-2013). In addition, medical compressed air should also be
Q: Oil-free air compressor is really oil-free? Answer: Water-lubricated air compressor is really oil-free. Use pure water to lubricate the compressed air to prevent oil from mixing into the compressed air, thereby avoiding pollution to the post-processing equipment. Using Shanghai Granklin Group
Large air compressor is widely used in many industries because of its high efficiency, stability and large flow. The following are some industries that mainly use large air compressors: Petrochemical industry: Application: Air passivation for urea reactors, ammonia pressurized storage,
In semiconductor plants, compressed air piping systems play a vital role. This system not only ensures the smooth production process, but also provides strong support for improving product quality and production efficiency. The compressed air pipeline system is mainly compressed by air
The quality requirements of compressed air in general factories mainly focus on core indicators such as oil content, dust content, dryness, etc. There are differences in standards in different industries and application scenarios, but the following specifications are generally followed: 1. oil content requirements Conventional standards: Most industrial scenarios require pressure
The ppm of air oil content represents the trace concentration of oil in the air, I .e. the amount of oil per million parts of air. Ppm is the abbreviation of English part per million, which means one part per million. Specifically, if the oil content in the air is X ppm, then
To make the gas of the air compressor anhydrous, the following measures can be taken: Cold and heat exchange technology: Pre-cooling treatment of the hot compressed air just produced, which helps to reduce the moisture content in the air. Install the drain valve: install the drain valve at the bottom of the air tank of the air compressor
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
