2026-04-10Views：
The oil content in the exhaust of an air compressor is usually expressed in ppm(parts per million, parts per million) or mg/m & sup3;(milligrams per cubic meter). Both units are used to quantify the amount of oil in a mixture of oil and gas, but they are measured and expressed differently.
ppm(parts per million): This is a proportional unit that indicates how many parts out of a million parts are oil. For example, if the oil content of the air compressor exhaust is 10ppm, it means that for every million parts of the exhaust gas, there are 10 parts of oil.
mg/m & sup3;(milligrams per cubic meter): This is a concentration unit that expresses how many milligrams of oil are contained in each cubic meter of gas. This unit more intuitively reflects the actual mass concentration of the oil.
The exhaust oil content of the air compressor depends on the type, design and maintenance of the air compressor. Oil-free air compressors should theoretically be able to provide very low exhaust gas oil content, usually much lower than 1ppm or the corresponding mg/m & sup3; value. The micro oil air compressor or lubricating oil involved in the compression process of the air compressor, the exhaust oil content will be relatively high.
In order to accurately measure the exhaust oil content of the air compressor, a special oil and gas analyzer or similar detection equipment is usually used. These devices can accurately measure the oil content in the exhaust gas and give readings in ppm or mg/m & sup3.
When choosing an air compressor, if the application scenario has strict requirements on air quality, such as food, medicine or electronics, it is very important to choose an oil-free air compressor that can provide low exhaust oil content. If the application scenario is not so strict on the air quality requirements, then you can choose a micro-oil air compressor, and configure appropriate oil and gas separation equipment as needed to reduce the oil content in the exhaust.
The general maintenance cycle of air compressors depends on many factors, including the type of air compressor, the operating environment, the workload, and the manufacturer's recommendations. Different air compressors may have different maintenance requirements and time intervals. The following is the general air compressor
Many people think that oil-free air compressors are truly oil-free, but this is not the case. Usually we think that the oil content of the oil-free air compressor is 0.01ppm, while the oil content of the screw machine we usually use is about 3ppm, which we will recognize above this standard.
As far as today's profile processing market is concerned, laser cutting, water cutting and other technologies have unparalleled advantages in a certain range. Fast processing speed, less waste of raw materials, low processing costs, the ability to process complex graphics, and so on, these advantages are beyond the reach of traditional blanking and milling. However, as an important supporting equipment, "air compressor" how to better apply to laser cutting machine has been the problem of many users.
The demand pressure of industrial compressed air varies for different applications and industries. The following is an overview of some common industrial compressed air pressure requirements and their application scenarios: General requirements: The compressed air pressure commonly used in industry is usually 0.7Mpa
Scroll air compressor and screw air compressor have their own advantages and applicable scenarios, the specific choice of which type depends on the actual needs and the use of the environment. The following is a comparative analysis of the two air compressors: 1. scroll air compressor Advantages: simple structure
As a new type of environmental protection equipment, the water-lubricated air compressor has excellent performance in energy efficiency and air quality, especially represented by the water-lubricated screw air compressor produced by the Glanklin Group. However, in the cold environment, users are generally concerned about a problem is: water
There is a close relationship between workshop gas consumption and gas supply. Simply put, the gas supply should meet the gas demand of the workshop, taking into account efficiency and cost. First of all, the workshop gas consumption refers to the amount of gas actually used by the workshop in the production process. This
The working time of the air compressor is not directly determined by the pressure, but is affected by many factors. First of all, the air pressure of the air compressor is set according to the work needs, and adjusting the air pressure can adapt to different process requirements. However, if the air pressure is adjusted too much, it may
In industrial production, the number of air compression is not fixed, but is restricted by multiple factors such as compression ratio, temperature, equipment type and efficiency. The following analysis is carried out from the three dimensions of technical principles, equipment limitations and practical applications: 1. the number of theoretical compressions.
When discussing the lubrication mechanism of oil-free compressors, the water-lubricated screw air compressor produced by Shanghai Granklin Group provides us with a clear answer. This air compressor abandons the traditional oil lubrication method and uses pure water as the lubricant to achieve high efficiency and ring
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
