2026-04-10Views：
Screw air compressor vibration reasons may be the following:
the deviation of the wheel center is large, which may be caused by the installation error, thermal expansion under the working state, deformation after bearing and uneven settlement of the unit foundation.
The bottom angle bolt is loose, if the bolt is not tight, it will also cause the air compressor to vibrate.
The rotor clearance does not meet the standard, which may be caused by rotor deformation or wear.
Insufficient supply of lubricating oil for the air compressor, or the oil filter has not been replaced for a long time, the poor working environment leads to blockage, and insufficient lubrication causes bearing wear and vibration.
The influence of condensed water, the condensed water with corrosive gas in the air will cause serious corrosion of the rotor, gas seal, diffuser and carbon steel air pipe, etc., resulting in the vibration of the air vortex.
Screw air compressor 2. four impeller welding parts cracking or impeller surface scaling will also lead to vibration. Cracking may be caused by improper welding process or material fatigue; scaling is caused by impurities such as dust or soot in the air entering the compressor and mixing with lubricating oil.
For the above reasons, you can try the following solutions:
find a professional air compressor maintenance engineer to readjust the wheel center to ensure that the deviation of the wheel center is within the allowable range.
Adjust and fasten the anchor bolts to ensure that the bottom angle bolts are fastened reliably.
Check the rotor for deformation or wear and repair or replace if necessary.
Check whether the oil supply regulating valve is fully open and increase the amount of lubricating oil; replace the new oil filter or clean the old oil filter to ensure smooth oil flow.
For the impact of condensed water, air filtration and drying can be strengthened to reduce the entry of corrosive gases and condensed water; at the same time, the rotor, gas seal, diffuser and carbon steel air pipes are regularly inspected and maintained.
For the problem of cracking or scaling of the impeller, it can be repaired by welding or replaced with a new impeller; at the same time, air filtration and fume treatment are strengthened to reduce impurities entering the compressor.
The above information is for reference only, it is recommended to consult professional technical personnel to obtain specific solutions.
The quality standard of fermentation air mainly includes the following aspects: microbial content: in the fermentation process, the air contains certain microorganisms, including bacteria, mold and yeast. These microorganisms play an important role in the fermentation process, but too many
Water-lubricated oil-free air compressors are widely used in many industries, including but not limited to: Food and beverage industry: In this industry, the production process requires high-quality air sources to ensure product quality and safety. Water-lubricated oil-free air compressor can keep the air source
The oil-bearing grade of compressed air of micro-oil air-cooled screw air compressor is usually Class 1 to Class 2 of ISO 8573-1 standard. Some high-end models can be optimized to approach Class 0 but need to rely on post-treatment equipment. The following is a specific analysis: 1. oil, etc.
The main air source pressure of automation equipment is usually set at about 5bar (about 0.5MPa), which is a balanced choice after considering the equipment performance, cost, safety and industry practice. The following is the specific reason analysis: 1. Meet the work needs of most pneumatic components
Granklin Water Lubricated Air Compressor Agency Consultation Instructions If you need to know about Granklin Water Lubricated Air Compressor Agency cooperation, you can contact through the following official channels: Contact number: 021-56021878 Email: service@vip.granklingroup.com Address: Shanghai
During the operation of the screw air compressor, the compressed air will carry a large amount of water (including liquid water and gaseous water vapor). If it is not effectively separated, it will cause equipment corrosion, pipeline blockage, and product quality degradation at the gas end. Gas-water separation is the post-treatment system of screw air compressor
Whether the medical air compression equipment room has explosion-proof requirements depends mainly on its specific environment and application requirements. The following is a detailed analysis of this problem: The necessity of 1. explosion protection requirements Environmental factors: If the medical air compression equipment room is located in a flammable and easy
As a special type of air compressor, oil-free screw air compressor has shown excellent performance in many application scenarios with its unique advantages. The following is a detailed analysis of the main application scenarios of oil-free screw air compressors: First, oil-free screw air compressors are used in medical
Whether the coal mine air compressor station needs explosion-proof depends on the specific environment and safety requirements. Generally speaking, as a special environment with combustible gas and dust, coal mine has strict requirements for the explosion-proof performance of electrical equipment. This is
The size of the common air pressure in the factory depends on the specific application scenario and requirements. In general, the factory normal air pressure usually refers to atmospheric pressure, I .e. standard atmospheric pressure, the value of which is defined as 101325 Pa pascals (Pa). However, in practical applications, the actual air pressure of the factory can be
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
