2026-04-10Views：
1. The operating environment of the air compressor should be below 38 ℃. Improve the ventilation system of the air compressor room, and increase the exhaust fan in the air compressor room to discharge the hot air, thereby reducing the temperature. (Note: A heat source with high temperature cannot be placed around the air compressor) If the temperature around the machine is relatively high, the temperature sucked by the machine will be too high, so that the oil temperature and exhaust temperature will also increase accordingly. These are all needs in summer. Attention
2. The radiator should be kept unobstructed and clean at all times. When the working conditions are dusty, the radiator should always clean up the dust on it to ensure that the first air sucked by the air compressor is smooth. The air compressor oil filter is blocked, causing the lubricating oil path to be unobstructed, and the amount of oil entering the host is too small, resulting in high temperature shutdown.
3. Check whether the cooling water temperature and water pressure are normal. The inlet water temperature of the air compressor is generally not more than 35 ℃, and the water pressure is between 0.3 and 0.5Mpa. At the same time, the scale of the cooler is removed to ensure the heat exchange efficiency. If the water temperature does not meet the requirements, the cooling tower can be installed in the appropriate position.
4. The three filters of air compressor mainly include: air filter, oil filter and oil and gas separator. Air filter blockage will cause the air compressor load is too large, long-term overload state, causing high temperature; oil core blockage will cause the internal pressure is too high, resulting in high temperature; oil filter blockage will cause the flow becomes smaller, resulting in high temperature.
The dust in the air sucked by the screw air compressor is blocked in the air filter. In order to prevent the screw compressor from being worn prematurely and the fine filter element in the oil and gas separator from being blocked, it usually needs to be more popular after a certain period of operation. At the same time, check whether the oil filter and the oil and gas separator filter need to be replaced.
Lack of oil in the air compressor or insufficient oil supply inside the machine will also cause the air compressor temperature to be too high. In hot summer weather, you should check the position of the oil and gas barrel oil level mirror oil. If the oil level is lower than the oil level mark, you should stop the machine and refuel to prevent high temperature. In addition, be sure to use genuine air compressor oil to ensure the operation of the air compressor.
6. In summer, in order to ensure the smooth operation and production of your air compressor, please maintain the air compressor equipment regularly ~
1. Traditional air power: pneumatic tools, rock drills, pneumatic picks, pneumatic wrenches, pneumatic sandblasting 2. Instrument control and automation devices, such as tool replacement of machining centers. 3, Air jet loom with compressed air
1, small maintenance: only need to replace the air compressor oil and oil filter, usually in the new machine running 500 hours to replace. 2. Major maintenance: In addition to replacing the air compressor oil and oil filter, it is also necessary to replace the air compressor air filter element, oil and gas separator core, motor grease, etc.
It is best to use the original lubricating oil or the lubricating oil recommended and specified by the manufacturer. One is the oxidation resistance and thermal stability of compressor oil. For compressor oil, its oxidation resistance and thermal decomposition resistance can not only prevent oil thickening, deposition and sludge formation, but also extend the service life of compressor oil, thereby saving the high cost caused by replacement, shutdown and oil cleaning;
Air compressor, referred to as "air compressor". It is a kind of power equipment, generally divided into power air compressor and volumetric air compressor, common centrifuge belongs to power type, screw type belongs to volumetric type. Compressed air is mainly supplied under pressure. It is used in pneumatic and pneumatic control, gas drive and chemical reaction.
baoding air compressor factory to buy products which company? shanghai granklin group air compressor factory, do a good job for you to buy air compressor and after sales service. Positive displacement compressor-directly rely on changing the gas volume to improve the gas
View detailsThe "air compressor head" produced by "Shanghai granklin group" is used in the "water lubricated air compressor" produced and sold by itself. for the "air compressor head", an enterprise specializing in the production and manufacture of "granklin air compressor", we strictly control the quality of the "air compressor head" under the condition of completely using the self-produced "air compressor head.
Granklin sales of air compressor use the scene is very much, the most common is a variety of air gun tire repair, but the role of air compressor is not only so there are more application scenarios. The role of air compressor.
Compressed air is widely used and is the second largest power energy after electricity. Therefore, air compressors, as general equipment, are widely used in various industries. Air occupies a certain space, but it has no fixed shape and volume. In the right
An air compressor is a device used to compress gas. Air compressors are similar in construction to water pumps. Most air compressors are of the reciprocating piston type. As an important form of energy generation, air compressor is widely used in all aspects of life and production. In particular, single-screw air compressors are widely used in machinery, metallurgy, electronic power, medicine, packaging, chemical, food, mining, textile, transportation and many other industrial fields, becoming the mainstream product of compressed air.
View detailsThe following points should be paid attention to during the operation of the oil injection screw air compressor: 1. When the operation occurs or abnormal vibration occurs, the machine should be stopped immediately for inspection; 2. There is pressure in the operating pipeline, and it is not possible to loosen the pipeline bolts and open unnecessary Valves, such as traps, drain valves, etc;
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
