2026-04-09Views：
Air compressor three filter mainly includes: air filter, oil filter, oil separator. The method of replacing each filter element is slightly different, and we will talk about it separately.
1. Air Filter Replacement
the dust in the air sucked by the screw air compressor is blocked in the air filter. In order to prevent the screw compressor from being worn prematurely and the fine filter element in the oil and gas separator from being blocked, it is usually necessary to clean or replace the air after 500H operation. Filter element; in dusty areas, the replacement time should be shortened. The filter must be shut down when replacing. In order to reduce the downtime, it is recommended to replace a new or cleaned spare filter element.
1) Facing a flat surface, tap the two end faces of the filter element in turn to remove most of the heavy and dry dust.
2) Blow with dry air less than 0.28Mpa in the opposite direction to the inhaled air, the nozzle is at least 25mm away from the folded paper, and blow up and down along its height.
3) If the filter element is found to be thinned, pinhole or damaged, it shall be discarded.
2. Oil Filter Replacement.
1) Unscrew the oil filter and discard it.
2) Carefully clean the filter housing and dredge the front and rear pressure difference through holes.
3) Check the performance of differential pressure transmitter.
4) Install oil on the new filter element (apply a layer of oil on the sealing ring of the filter element).
5) When installing the filter element, screw it until it touches the gasket, and then manually tighten 1/3 turn
6) After starting up, check whether there is any leakage.
Note: The filter element can only be replaced after the compressor stops running and releases the pressure. In addition, you must be careful to heat the oil to prevent burns and do not spill the oil.
3. Oil Separator Filter Element Replacement
1) Remove the connecting hoses and copper pipes on the minimum pressure valve.
2) Remove the return pipe copper pipe.
3) Remove the cover plate.
4) Pull out the filter element.
5) Clean the cylinder.
6) After replacing the filter element, install it in reverse order.
Note: Before installation, you must check whether the rubber and asbestos pads have anti-static properties (conductive nails must be installed). During installation, it is necessary to prevent unclean objects from falling into the oil drum. When installing the return pipe, it must be ensured that the pipe is inserted into the bottom of the filter element.
In the field of compressed air equipment, screw machines and scroll machines have their own advantages and disadvantages, and their advantages and disadvantages also directly affect the user's choice. The water-lubricated screw air compressor produced by Shanghai Granklin Group stands out in the screw machine market with its unique technical advantages. Screw machine
The pressure setting of the bottle blowing machine is not fixed, but adjusted according to the specific model, bottle type and production requirements. The following are some considerations and suggestions about the pressure setting of the bottle blowing machine: model and bottle type: different bottle blowing machines and bottle types need pressure
The air compressor room of the food factory shall meet the requirements of site selection, environment, equipment layout, safety protection, air quality, daily management and other aspects. The details are as follows: 1. site selection and layout site selection requirements: a wide place with good lighting shall be selected, away from explosive,
Water lubricated screw air compressor is a kind of screw air compressor which uses water as lubricating medium. It has the advantages of environmental protection, safety and high efficiency, and has a wide range of application prospects in many fields. The following is a detailed evaluation of water lubricated screw air compressor: 1. advantages
Air compressors with oil and without oil are not absolutely good or bad. Their use occasions are different from those suitable for working conditions. If they are used for purging, machining, manufacturing and power, it is OK to choose air compressors with oil and slight oil, but in some occasions, oil-free air must be used.
In the medical field, the air compressor provides the necessary compressed air for the ventilator, which is the main function of the air compressor on the ventilator. The ventilator uses the compressed air provided by the air compressor to drive its internal pneumatic components to achieve respiratory therapy. Specifically
The coalbed methane compressor is a key equipment specially used in the process of coalbed methane mining and transportation. The following is a detailed explanation of coalbed methane compressor: 1. definition and use Coalbed methane compressor, as the name implies, is used to compress coalbed methane (also known as coal mine gas or coal seam A
The main differences between air compressor frequency conversion and power frequency are reflected in the working principle, energy efficiency performance, starting characteristics, noise level, pressure stability, maintenance costs, and applicable scenarios. The following is a detailed summary of these differences:
The reasonable range of air compressor vibration value may vary according to different standards, equipment models and application scenarios. Generally speaking, the vibration value of the air compressor host can be regarded as normal within the following range: the vibration value in the horizontal direction does not exceed 0.2mm (vibration of the machine base),
The pressure of the air compressor usually depends on its design and application requirements. In general, the pressure range of industrial air compressors is between 0.7 and 1.2 megapascals (MPa), which is equivalent to 7 to 12 bar (bar). This pressure range is usually sufficient for most industrial production.
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
