2026-04-09Views：
Domestic machine generally 2000-3000 hours once, about once every six months.
Hello, the first maintenance of the air compressor is usually once every 500 hours.
The first guarantee is relatively simple, just replace the oil and filter. After the maintenance is generally about 2500-3000 hours, but also related to the site environment of the air compressor, if the site environment is too bad, the maintenance time interval may be shorter, after the maintenance needs to replace the oil, air filter, oil filter, oil.
1. The air compressor oil should be replaced once every 2000 hours or 3 months. It needs to be replaced every time. First, drain the oil in the oil-gas separator, then drain the oil cooler oil, then jog for 3 seconds, stop, clean the oil in the inner cavity of the main engine head, add 2 liters of new oil, jog for 3 seconds, clean the engine head, add 5 liters of oil to the main engine head, do not jog, and finally fill up the oil separator oil, then jog the machine for 5 seconds, press the stop button, the oil will descend, and then add oil to the two red lines of the oil level gauge.
2. The oil filter element is replaced with the oil, 2000 hours or 3 months of operation. When replacing, fill up with new oil, and apply a layer of oil on the O-ring, install it, and do not leak oil.
3. The air filter element is replaced only when it is blocked. It is usually cleaned every 500 hours, and the use is not higher than 0.
4Mpa pressure gas purges from the inside to the outside, and then cleans up the dust outside
4. The oil and gas separator has a filter element, which is generally replaced in 4000 hours or 6 months of operation. When replacing, it must be replaced when the oil is replaced. After replacement, it needs to run for half an hour and then stop. Let the oil core adapt to the work, wait another hour, and finally Run normally,
.
5. Water-cooled cooler, cleaned once every six months, scale and grease should be cleaned with cleaning agent,
6. The oil cut-off valve should be checked regularly. The copper pipe should be removed from the bottom, and the copper pipe should be pushed up with iron wire. It is better to top it up and return it after let go. Otherwise, it needs to be removed and cleaned.
7. Every summer before the machine needs a major maintenance:
a Remove the oil cooler, soak the oil system with carbon cleaning agent for one day, and then clean it.
B cooling fan blades to clean the surface dust
c motor bearing to add new butter and cleaning motor fan blade surface dust
The pressure of the air compressor varies due to its design, use and operating environment. The following is the general pressure range of air compressors according to different application scenarios and types: Mini air compressor: The pressure range is usually between 1 and 5bar.
Whether the compressed air tank belongs to special equipment depends on its design pressure and volume. According to publicly released information, only industrial compressed air tanks with a design pressure greater than 0.1MPa are regarded as special equipment and need to be managed in accordance with specific laws and regulations.
The difference between power frequency air compressor and permanent magnet variable frequency air compressor is mainly reflected in the following aspects: motor type and efficiency: power frequency air compressor usually uses squirrel cage motor, and there will be 7%-15% loss in the process of converting electrical energy into kinetic energy. permanent magnet frequency conversion
The pressure of air compression pipeline in clean area workshop should be determined comprehensively according to industry specifications, equipment requirements and system efficiency. The following is specific guidance: 1. conventional pressure range Pharmaceutical/electronic industry: The pressure of compressed air pipeline in clean area is usually 5-7 bar (gauge pressure). Food
The replacement cycle of the air compressor pipe filter element depends on many factors, including the use environment of the air compressor, air quality, running time, and the type and quality of the filter element. Usually, the manufacturer of the filter element will provide a recommended replacement cycle, which can be used as a reference.
In modern industrial production, the purity of oil-free compressed air has become the focus of attention in many industries. As a leader in the field of air compression, the water-lubricated screw air compressor produced by Shanghai Granklin Group has won the market for its excellent performance and ultimate purity.
Chlor-alkali chemical plant is through the electrolysis of salt water to produce chlorine, hydrogen and caustic soda factory, the use of compressed air throughout the production process is very much, can be said to be a source of power plant operation can not be separated.
The load running time of the air compressor does not have a fixed standard, it depends on a variety of factors, such as the type of air compressor, application, workload and maintenance conditions. Here are some general guidelines: Regular working hours: Pass
When answering the question of how many kilograms of air pressure is special equipment, we first need to clarify the definition of "special equipment. According to publicly available information, special equipment usually refers to equipment that is more dangerous to personal and property safety.
There are significant differences between fixed-frequency screw machine and variable-frequency screw machine in many aspects. The following is a detailed comparison: 1. working principle and operation mode Fixed-frequency screw machine Working principle: The working principle of fixed-frequency screw machine is similar to that of ordinary screw compressors, through a pair
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
