2026-04-10Views：
Screw compressor vibration value of national standards, but a bit "serious" topic! However, I will try to explain it to you in a soft and interesting way.
Imagine that a screw compressor is like a chef in a large kitchen, its "agitator" (screw) is constantly rotating and working. However, how can we judge the cook's craftsmanship? At this time, the "judge" of vibration value appeared.
The state stipulates that the vibration value of the screw compressor should be controlled within a reasonable range, just like the chef's mixer can not shake too much, otherwise it will affect the quality of the "dishes" (compressed air). The specific vibration value standard will vary according to different models and specifications. However, in general, the vertical vibration speed at both ends of the motor should not exceed a certain value, such as 0.35 mm/s, and the horizontal vibration speed is also limited.
If the vibration value exceeds the national standard, then be careful! It may be that there is a problem inside the screw compressor, and it is necessary to "ask the doctor" (maintenance personnel) to "cure" (maintenance) it in time.
In short, understanding the national standard of the vibration value of the screw compressor is as important as understanding the craftsmanship of the chef. I hope this interesting metaphor will help you better understand this topic!
The air supply pressure used in the machining workshop is usually in the range of 0.5~0.8 MPa(5~8 bar), but the specific pressure value should be determined according to the equipment type, process requirements and safety specifications. The following is a detailed analysis: 1. common equipment air supply pressure demand pneumatic
There are obvious differences in the design and operation principle of micro-oil and oil-free screw compressors. The following are the main differences between them: Lubrication method: Micro-oil screw compressor: Use a very small amount of lubricating oil to lubricate the screw rotor and bearings. These lubrication
Oil-free compression classification Oil-free air compressors are divided according to whether the compressed air contains oil or not, corresponding to oil air compressors or micro-oil air compressors. Oil-free air compressors are distinguished according to different compression forms or different host structures, and several common oil-free air compressors are used.
There are significant differences between the cold dryer and the suction dryer in terms of working principle, water removal effect, energy loss, gas loss and failure rate. The details are as follows: 1. working principle Cold dryer: Based on the principle of freezing and dehumidification, the refrigeration system reduces the compressed air Temperature makes water vapor
The power required for an air compressor with a capacity of 1 cubic meter per minute is not a fixed value, but is affected by many factors, including exhaust pressure, working environment temperature, air inlet temperature, air quality requirements and equipment stability requirements. to
The start and stop sequence of air compressor, cold dryer and suction dryer is very important to ensure the quality of compressed air and the stable operation of the system. The following is the recommended start-stop sequence: Start sequence Start the cold dryer: The main function of the cold dryer (freeze dryer) is to reduce the pressure
The continuous working capacity of the oil-free air compressor head depends on its design reliability, heat dissipation efficiency and the durability of the core components. Granklin water lubricated single screw air compressor can support long-term stable operation through the following technical characteristics: 1. Lubrication and heat dissipation synergy
Whether the air compressor needs to be closed depends on the specific use and demand. Under normal circumstances, in order to save energy and extend the life of the equipment, the air compressor should be turned off when it is not in use. However, in some specific situations, such as the need to continuously supply air or maintain system pressure
Generally speaking, oil-free air compressors do not contain oil at all. Truly oil-free is the all-oil-free air compressor. The air compressor lubricated with water is the real oil-free air compressor. Generally speaking, the oil content of oil-free air compressors is very small. So...
Air compressor: the core power source in general industrial equipment-analysis of granklin air compressor industry adaptability air compressor (air compressor) as the basic equipment in the industrial field, because of its widely used in manufacturing, energy, medical, food and other
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
