2026-04-10Views：
The problem of excessive moisture in the air compressor can be dealt with in the following ways:
cooler treatment: A cooler is a device that removes moisture from the air by condensation. The cooler of the air compressor can be replaced or maintained regularly to ensure its efficient operation and reduce the exhaust temperature and water content. In addition, the selection of efficient cold drying equipment can also improve the dehumidification effect.
Dryer treatment: The dryer is a kind of equipment that absorbs the moisture in the air through the adsorbent to make it dry. Common dryers are adsorption dryers and freeze dryers. You can consider replacing or maintaining the dryer to ensure that it is working properly to remove moisture from the air. For the adsorption dryer, it is necessary to periodically regenerate or replace the desiccant; for the refrigerated dryer, it is necessary to ensure the normal operation of the refrigeration system.
Oil separator treatment: The lubricating oil in the air compressor equipment will absorb the moisture in the air, so it is necessary to use the oil separator to separate the moisture and the lubricating oil. The oil separator can be checked and replaced to ensure its normal operation, thereby reducing the impact of moisture on the equipment.
Drainage treatment: a drain valve is installed in the compressed air pipeline to discharge the precipitated moisture regularly to achieve the purpose of dehumidification. The location of the drain valve is generally at the bottom of the gas pipeline. Drainage through the drain valve can effectively reduce the amount of moisture in the system.
Strengthen daily management: It is also important to do a good job in the daily management of air compressors. For example, keep the body clean and no leakage, check the accessory equipment of the air compressor, formulate the condensate discharge schedule according to the humidity and temperature conditions, discharge once a week under normal conditions, and discharge once a day in low temperature or high humidity climate. Clean the cooler with degreaser every week to reduce the exhaust temperature, and clean and replace the equipment regularly. These measures can effectively reduce the water content of the air compressor.
In summary, by using the above method to deal with the problem of excessive moisture in the air compressor, the normal operation of the air compressor can be ensured, the life of the equipment can be extended, and the operating efficiency of the equipment can be improved. At the same time, it is also necessary to pay attention to selecting the appropriate method for processing according to the specific situation.
The imbalance of the air compressor host may have the following reasons: the host is not aligned during installation, that is, the vertical and horizontal installation planes are not found, which may lead to imbalance when the host is running. In order to ensure the smooth operation of the air compressor, the main
In the field of air compressor, the relationship between pressure and gas production is not a simple linear relationship, but is affected by a variety of factors. The phenomenon of "the greater the pressure, the smaller the gas production" can be explained from the following aspects: 1. physical principles
The calculation of the gas consumption of the equipment needs to select the corresponding method according to the specific gas type and equipment characteristics. The following are the detailed calculation methods and precautions: 1. the calculation formula of the gas consumption of compressed air: Q = 273.15 & sdot;(1 0.00367T)V & sdot;P Q: for compressed air
The calculation of suction volume by compressor discharge volume should be combined with thermodynamic principle and compressor performance parameters. The specific steps are as follows: 1. the core formula derivation According to the law of conservation of mass: Q_{suction} = Q_{row} times frac{P_{row }}{ P_{suction}} times frac {
The choice of 20 cubic air compressor depends on your exhaust pressure. The 20 cubic parameters of granklin GW series intelligent energy-saving water lubricated oil-free screw air compressor are as follows. The GW132W water lubricated oil-free screw machine can reach 23.10 m/min at a working pressure of 0.8Mpa, 19.97 m/min at a pressure of 1.0Mpa, and 16.9 m/min at a pressure of 1.25Mpa. The noise is about 78 decibels. The high-power air compressor must be far away from the crowd when working, otherwise it is too noisy.
View detailsThere may be many reasons for the loud sound of the screw machine. The following are some possible reasons: The main engine is unbalanced: When the screw compressor is running, if the rotor of the main engine is unbalanced, vibration and noise will be generated. This may be due to rotor design or manufacturing issues, or
Air compressor suction pressure standard range and application scenario analysis The suction pressure of the air compressor is the core operating parameter, and its set value is directly related to equipment efficiency, energy consumption and service life. The following from a professional point of view, combined with industry norms and typical applications
The pressure of the compressed air in the factory will generally be determined according to the specific application requirements and equipment specifications. Generally, the normal pressure range of industrial compressed air is 0.6~0.8MPa, but in practical applications, this range may be changed. In some common jobs.
In the medical field, the purity of compressed air is extremely high, especially the oil content. The medical level 0 oil-free standard, as one of the most stringent standards, requires that the oil content in compressed air must be extremely low to ensure the normal operation of medical equipment and the safety of patients. Shanghai Haige
The reasons for the widespread use of air compressors on the construction site can be summarized as follows: 1. provide power support to drive pneumatic tools: air compressors can provide stable air pressure for pneumatic tools on the construction site, such as pneumatic drills, pneumatic screwdrivers, spray guns, Pneumatic conveying system
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
