2026-04-10Views：
The air blown by the air compressor is all water, which may be caused by the following reasons:
the moisture content in the air is large: when the air is compressed, it will become supersaturated, and the water in the air will separate out and become a liquid. The moisture content in the compressed air is related to the humidity of the air, such as the environment in the room is too humid, or seasonal reasons, it will make the water content in the air exceed.
Drain valve or dryer failure: the automatic drain of the air compressor itself is blocked or the automatic drain of the air storage tank is blocked, or the dryer fails and does not work normally, which will cause the air blown out by the air compressor to contain a lot of water.
The compression process produces water: the internal temperature of the air compressor is very high when it is working, and the water in the natural air inhaled will form water vapor during the operation of the air compressor. As the compressed air is discharged, it encounters cold air, and the water vapor condenses into water.
In view of the above problems, the following optimization measures can be taken:
reduce environmental humidity: Keep the environment in the computer room dry, you can use air conditioners, dehumidifiers and other equipment to reduce environmental humidity, thereby reducing the moisture content in the air.
Check and repair the drain valve and dryer: regularly check whether the automatic drain of the air compressor and the automatic drain of the air storage tank are blocked. If there is any blockage, clean it up in time. At the same time, check whether the dryer is working properly, if there is a fault, it should be repaired or replaced in time.
Increase post-processing equipment: increase the corresponding post-processing equipment at the back end of the air compressor, such as cold dryer, suction dryer, etc., to further process the compressed air to remove the moisture and oil and other impurities, to ensure that the compressed air is dry and clean.
Adjust the parameters of the air compressor: adjust the parameters of the air compressor according to the actual situation, such as reducing the exhaust pressure, reducing the compression ratio, etc., to reduce the amount of water vapor generated during the compression process.
Strengthen maintenance: regularly maintain the air compressor, clean up the internal impurities such as scale and carbon deposits, keep the air compressor in good condition and extend its service life.
In summary, by taking the above optimization measures, the problem that the air blown by the air compressor is all water can be effectively solved, and the quality and dryness of the compressed air can be improved.
The oil content of the compressed gas of the oil-injected screw air compressor depends on the equipment performance, maintenance status and the configuration of the end purification device. The following is an authoritative interpretation based on industry norms and technical parameters: 1. core working principle and oil content relationship oil injection lubrication mechanism Spray
The screw air compressor can be operated for 24 hours. The air pressure is not enough to load automatically, the air pressure is enough to unload automatically, and the idle time exceeds the rated time to stop automatically, thus realizing unattended for 24 hours. Air compressor can insist on continuous work.
The air compressor power corresponding to the 37kw motor is 37kw. However, to convert it to horsepower (HP), the following calculation can be referred to: 1 horsepower (HP) is approximately equal to 0.75 kW (KW). Therefore, the 37 kW (KW) of the air compressor corresponding to the horsepower (HP) can pass 3
The dust content in the exhaust of the micro-oil screw air compressor usually needs to be controlled at ≤ 1 mg/m & sup3;, dust particle size ≤ 3~5 μm, so as to meet the basic requirements of air cleanliness in general industrial scenarios. The following is a detailed analysis of this problem: micro-oil screw air compressor in
In food production, compressed air directly contacts food or production equipment, and its quality directly affects food safety. The following are the core standards and application specifications of compressed air for food: 1. international general standards 1. ISO 8573-1:2010 quality grade solid particles
The power of oil-free screw air compressor and oil-injected screw air compressor is not directly determined by its lubrication method (oil-free or oil injection), but by the specific design, manufacturing process and the performance of core components such as motors. Decided. Therefore, it cannot be simply said
In the highly sophisticated chip packaging industry, compressed air is not only an important power source for production line operation, but also a key factor to ensure packaging quality and product yield. The quality of compressed air, including its dryness, cleanliness and pressure stability, is directly related to the chip
In industrial production, the stable air supply of air compressor is very important for the continuous operation of the production line. Regarding the question of whether the air supply will be affected when the air compressor is pumping, the water-lubricated screw air compressor produced by Shanghai Granklin Group is given with its unique design and high efficiency performance.
When discussing the efficiency of screw air compressors and centrifugal air compressors, we first need to understand the basic working principles and characteristics of these two air compressors. Screw air compressor, its working principle mainly depends on the two intermeshing screw gas compression. This air pressure
There are significant differences between micro-oil air compressor and oil-free water lubrication air compressor in terms of lubrication medium, air quality, energy consumption efficiency, maintenance cost and applicable scenarios. The specific analysis is as follows: 1. lubrication medium and working principle Micro-oil air compressor: By injecting less into the screw cavity
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
