2026-04-10Views：
The maintenance cycle of the new screw machine can be determined by referring to the following aspects:
first of all, under normal circumstances, the maintenance of the screw machine can be divided into daily maintenance and major maintenance. Daily maintenance is mainly the daily maintenance and cleaning of the equipment, the general recommended cycle is 1-2 months; major maintenance requires thorough inspection and maintenance of the equipment, the recommended cycle is 6-12 months. The specific maintenance cycle should also be adjusted according to the model of the equipment, the frequency of use and the working environment.
Secondly, the air compressor oil and oil filter in the screw machine need to be replaced regularly. The oil core should be replaced after the new machine runs for 500 hours for the first time, and then it can be replaced every 2000 hours of operation. In addition, for the major maintenance of the screw air compressor, in addition to replacing the air compressor oil and oil filter, but also to replace the air compressor air filter and oil and gas separator core, motor grease, etc., this maintenance is generally recommended in the machine running for 3000 hours or so. However, if the working environment is poor, such as a lot of dust, this time should be shortened appropriately.
In addition, the cooling system of the screw machine is also very important. It is necessary to regularly clean the scaling inside the cooling system and check whether the cooling water is replaced in time to maintain the normal operation of the equipment.
In addition, cables and connectors are also parts of concern. During the operation of the screw machine, there may be cable aging, poor connection, etc. Therefore, it is necessary to check whether the cable and connector are normal during each maintenance to ensure that there is no loosening and falling off.
Finally, the screw in the screw machine needs the support of lubricating oil to work normally. Therefore, the replacement of lubricating oil is also very important. The generally recommended replacement cycle is about 6 months.
To sum up, the maintenance cycle of the new screw machine will change due to a variety of factors. The above is a general suggestion, and the specific implementation should be determined according to the actual situation. In addition, in order to ensure the effectiveness of maintenance, it is best to be operated by professional maintenance personnel.
The standard of oil content of lithium battery compressed air is usually very strict, because the quality of compressed air in the production process of lithium battery is very high. The following is a detailed summary of the standard of lithium battery compressed air oil content grade: oil content grade: lithium battery
If the pursuit of high efficiency and energy saving, pure compressed air and intelligent management, the use of Shanghai Granklin Group water lubrication technology of permanent magnet variable frequency air compressor is a better choice.
6kg air compressor technical parameter analysis and selection guide In the field of compressed air system, "6kg air compressor" is a common technical expression in the industry, and its core parameter definition and engineering application are as follows: 1. basic parameter analysis "6kg" refers specifically to the rated discharge pressure of air compressor
In the pharmaceutical workshop, compressed air is widely used and important, which is embodied in the following aspects: 1. equipment drive and operation Pneumatic equipment drive: Compressed air is the main power source of many pneumatic equipment in the pharmaceutical workshop. For example, pneumatic valves, pneumatic pumps,
Q: What is the compressed air standard in the food industry? Answer: The food industry has very high requirements for compressed air standards, mainly including the following aspects: Purity: The food industry requires that compressed air must be oil-free and tasteless to ensure food quality and quality.
Oil-free air compressor, as can be seen from the name, it is an air compressor that does not require lubricating oil. This special design does bring us a lot of benefits. First of all, it's really good at storing air. As long as you add a gas tank, you can easily
The standard compressed air consumption of numerical control lathe (numerical control machine tool) varies depending on the equipment configuration, process requirements and production rhythm. The reference air consumption of a single numerical control machine tool is usually 0.3m & sup3;/min to 1.5m & sup3;/min, depending on the equipment work
In the food industry, the quality requirements of compressed air are very strict to ensure the safety and hygienic quality of food. Among them, the dew point temperature is one of the important indicators to measure the quality of compressed air. The following is a detailed explanation of the compressed air dew point requirements for the food industry
Screw air compressor motor speed varies according to equipment type and application scenario, the following is a detailed answer: 1. speed range standard national standard According to GB/T standard, the motor speed of screw air compressor is divided into two gears: 2-pole motor: synchronous speed 3000rpm, actual air compressor
2 cubic air compression tank belongs to special equipment. In general, the air storage tank we refer to generally refers to the equipment used to buffer compressed air with a volume greater than or equal to 0.1 cubic meters and a pressure greater than or equal to 0.8Mpa. These are all pressure vessels, so conceptually, these are all
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
