2026-04-09Views：
There are significant differences between water-lubricated oil-free air compressors and traditional air compressors in many aspects.
Lubrication method:
water-lubricated oil-free air compressor is lubricated and cooled with pure water, and the body is made of special medical grade stainless steel, which will never corrode.
Traditional air compressor usually rely on lubricating oil to cool, the body will have the smell of oil.
Cooling effect and temperature:
water lubricated air compressor system pure water has been circulating in the system, the system will automatically change the water at a set time to ensure the water quality, the body working temperature is not higher than 50 degrees, so the water in the body is not affected and scale problems.
The working temperature of the traditional air compressor is very high, exceeding 200 degrees, which directly affects the life of the cooling oil and the bearing.
Bearings and Efficiency:
the water-lubricated oil-free machine adopts imported special bearings, and there is no problem with direct water lubrication. The machine head has high efficiency, low noise and few bearing combinations.
Traditional air compressors generally use ordinary bearings, short life and high noise.
Energy consumption:
the water-lubricated oil-free machine sprays pure water directly into the body. Due to the high specific heat value of water, the compression chamber is almost in the ideal state of isothermal compression, which is the compression process with the lowest energy consumption.
The cooling oil of the traditional air compressor is about 100 degrees, the temperature of the compression chamber exceeds 200 degrees, and the temperature difference is relatively large, so the energy consumption is relatively high.
Maintenance and cost:
the water-lubricated oil-free machine body is directly connected to the motor, the speed is lower than 3000 rpm, there is no speed-increasing gear, the bearing life is long, and the maintenance cost is low.
The traditional air compressor body and the motor should be between the acceleration and deceleration gear. Because the speed is above 18000 rpm, the speed-increasing gear is required to accelerate, the bearing life is short, and the maintenance cost is high.
In summary, there are significant differences between water-lubricated oil-free air compressors and traditional air compressors in terms of lubrication methods, cooling effects, bearing types, energy consumption, and maintenance costs. These differences make water-lubricated oil-free air compressors have higher efficiency and longer service life in many applications.
Power frequency screw machine can be frequency conversion in theory, but in fact, the installation of frequency converter can not achieve the expected energy-saving effect, but may bring a series of problems. The analysis is as follows: the energy-saving effect is limited: even if the power frequency screw machine is equipped with a frequency converter, the adjustment range is also limited, usually
The water content of the product after treatment is a range value, usually between 2% and 10%, but the specific water content will vary due to various factors such as material conditions, working conditions and models. 1. Factors Affecting Water Content Material Situation: Different Raw Materials Treated with Water Content
The frequency of air compressor maintenance mainly depends on a number of factors, including the use of air compressor, operating environment, operating time and pressure. The following is a clear overview of the frequency of air compressor maintenance: maintenance according to the frequency of use: for frequent use
Minor maintenance only needs to replace the air compressor oil and oil filter, which is usually replaced after 500 hours of operation of the new machine. Major maintenance is carried out about 3000 hours of operation of the machine, and the air filter element of the air compressor, oil and gas separator core, motor grease, etc. Air compressor recommended
There are significant differences between oil-free compressors and micro-oil compressors in many aspects, which are mainly reflected in the working principle, compressed air quality, operating costs, maintenance requirements, performance and so on. The following is a detailed analysis of the difference between the two: 1.
Which is the best permanent magnet frequency conversion energy-saving air compressor: Shanghai granklin group water lubricated screw air compressor stands out in today's industrial field. as an important power equipment, the performance and efficiency of air compressor are directly related to the production cost and operation efficiency of the enterprise. And in the public
There are some differences between screw compressors and scroll compressors in terms of structure, working principle and application. Structure and working principle: Screw compressor: It is composed of a pair of parallel arrangement and intermeshing male and female rotors (ie screws). When the rotor turns
Question: What size of air compressor is needed per hour for 75 cubic meters of air volume? Answer: If the air volume required per hour is 75 cubic meters, then 1.25 cubic meters per minute. If the Granklin water lubricated air compressor is 11kw, the gas production of 8kg of conventional pressure can meet the requirements. Snail
High-quality choice for safe medical oil-free air compressors In the medical field, pure, oil-free compressed air is essential because it is directly related to the health and safety of patients. Therefore, it is particularly important to choose a high-quality and safe medical oil-free air compressor.
Screw compressors and scroll compressors are two common types of positive displacement compressors, which are widely used in industrial fields, but their design principles and structural characteristics are different. The following is the core difference between the two: 1. Working principle type screw compressor vortex
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
