2026-04-09Views：
1. preparation
before starting the vehicle, check the amount of lubricating oil in the oil-gas separator. If the oil level is too low, add oil to the specified oil sight glass level.
2. Start
open the air supply valve, press the start button, the unit will delay operation for 15 seconds, observe whether the pointer of the pressure gauge slowly rises to 0.25~0.4Mpa, run for a period of time, check whether the instruments and indicator lights are normal; Whether there is leakage in the oil and gas pipelines; Whether the oil level is within the specified range; Whether the exhaust pressure gradually rises to the set upper limit value.
3. operation
periodic checks in operation:
1, oil and gas separator lubricating oil quantity, oil level is too low should stop, until the air pressure drops to "zero" can open the cover to add oil.
2. The exhaust temperature should not exceed 110 ℃.
3, when the compressor working pressure reaches the upper limit should be able to automatically unload, to the lower limit should be able to automatically load.
4. parking
1. After closing the air supply valve, press the stop button to stop the motor.
2. Cut off the power supply
5. emergency stop
1. During the operation of the unit, when an abnormal situation is found, the emergency stop button can be directly pressed to stop the operation. Observe the indicator light and the condition of the unit, and cut off the power supply. Find out the cause of the fault and start it again after handling it. The emergency stop button must be reset.
2. Emergency stop shall be made under the following conditions:
the exhaust temperature exceeds the set value; the motor is overloaded but the overcurrent protection device does not operate; the solenoid valve is out of control; the lubricating oil cannot enter the unit for lubrication.
The quality requirements of compressed air in general factories mainly focus on core indicators such as oil content, dust content, dryness, etc. There are differences in standards in different industries and application scenarios, but the following specifications are generally followed: 1. oil content requirements Conventional standards: Most industrial scenarios require pressure
In the compressed air system of the semiconductor factory, there is a close relationship between the cold dryer (ie, the freeze dryer) and the air compressor. The main function of the cold dryer is to reduce the temperature of the compressed air, so that the water vapor in it is condensed and discharged, thereby providing dry compression
In the compressed air system, the dust content after 5-stage filtration is a key quality indicator, which directly affects the applicability of compressed air in industrial production. The following are professional answers based on international standards and industry practice: 1. 5-level filtration standards and dust content
There is a close relationship between the different gas consumption of the factory gas source and the diameter of the gas supply pipe. In the factory production process, the demand for gas varies from equipment to equipment, which requires that the gas supply system must be designed and configured according to the actual needs of the corresponding pipe diameter. First, use
The air compressor of the ventilator, like the little heart of the ventilator, beats to inject vitality into the ventilator. This small heart can be powerful, it can continuously provide stable, high-pressure, clean air for the ventilator, so that the ventilator can work smoothly,
The automatic drainage of air compressor tank is mainly realized by automatic drainage valve. The following is a detailed introduction to the automatic drainage of the air compressor gas tank: The working principle of the automatic drain valve: There is usually an air bottle or buoy in the automatic drain valve. When the storage
The oil content in the exhaust of an air compressor is usually expressed in ppm(parts per million, parts per million) or mg/m & sup3;(milligrams per cubic meter). These two units are used to quantify the oil content of oil and gas mixtures, but their measurement methods and tables
Analysis of Water Removal Technology of Air Compressor If the moisture in compressed air is not removed in time, it may cause pipeline corrosion, pneumatic component failure, product quality decline and other problems. The following is a systematic introduction to the water removal method of the air compressor from both technical principles and applicable scenarios.
In order to generate a pressure of 1.5mpa (megapascals), the discharge pressure of the air compressor needs to be greater than or equal to 1.5mpa. The specific air compressor size (such as power, exhaust volume, etc.) will also be affected by other factors, such as compressed air flow requirements, application scenarios, etc.
The compressed air of 0.6MPa is not absolutely safe in the production process, and its safety depends on the specific use scenario, equipment condition, operation specification and whether the protective measures are in place. The following is a detailed analysis of its safety: the risk of compressed air itself pressure wind
2018 Granklin Group. All rights reserved 沪ICP备18000439号-2
